1. Installation of the Wall Bracket
Wall Bracket is locked to LivionKey30 for the shipment. Take 2 keys from the backside of the LivionKey30 (attached with tape inside the enclosure).
Open the lock located in the bottom of the device with the key. Once the lock is opened, the wall bracket can be removed.
Install the Wall Bracket on the wall to the suitable place using at least 6 screws and anchors/plugs. Ensure that you have a power outlet near.
Recommended screw positions (marked as green)
Important!
LivionKey30 must be installed always in a warm and dry (non-condensing) environment! Cold or condensing conditions may cause malfunctions or damage the device.
The installation of the wall bracket must be done very carefully to ensure that it can carry the weight of the device.
In order to lift and lock LivionKey30 to wall bracket, ensure that there's approximately 20cm free space above and below the bracket.
2. Mounting LivionKey30 to the Wall Bracket
Turn on the LivionKey30 from the power switch. Don’t connect the power supply to the power outlet yet. When the led in the front panel is steady blue, the LivionKey30 is up and running normally. This takes approximately 90 seconds.
Location of the power switch
Note!
During the start-up, the device moves the key drum. Ensure there’s nothing inside the device then.
If the device has been stored for a long time, the battery might be empty. In this case the device will not start until it’s connected to the power outlet.
Lift LivionKey30 carefully to the Wall Bracket and check that it’s properly in place. Pay attention that the lock is in the open position before you lift the device to the Wall Bracket:
Secure the lock and remove the key. The device cannot be removed from the Wall Bracket now.
Connect the power supply to the power outlet.
Add a “Recording camera surveillance” sticker (included in the shipment) to the device's front panel. Alternatively you can use your own sign to indicate about the camera surveillance for users.
Clean dirt and fingerprints from the device by using specific stainless steel care spray.
3. Use of LivionKey30
3.1 Web applications
LivionKey30 is managed remotely from the LivionKey Dashboard or LivionKeyRegister web applications.
Navigate to address https://app.livionkey.com and login to the system with credentials created by your administrator or reseller. Depending on your credentials you will have access to LivionKey Dashboard or LivionKeyRegister.
Instructions on how to take your device in use in LivionKey Dashboard or LivionKeyRegister can be found on our support pages https://support.livionkey.com. Support pages include also other instructions for every-day use and other important documentation. Please study documentation carefully before use.
3.2 Inserting keys to LivionKey30
The keys can be inserted to LivionKey30 by opening the lockers from web applications or by entering valid pin-codes to the device's keypad.
It’s recommended to insert only 1 key with a ring and fob in one locker.
To ensure that camera-based key detection works without problems, the use of light colored keys / key fobs should be avoided.
Warning!
The locker must not be inserted too full. If there are many keys, key fobs and rings in the same locker, those may get in tension against the door or front panel. This may cause malfunction to the door or to the key drum.
It’s strictly prohibited to insert ribbons, strings, plastic bags, paper or any other thin and flexible objects to locker! These objects may get stuck in the LivionKey30 and cause malfunctions and break the device.
3.3 Support and online documentation
Livion technical support can be reached straight from support widget on web applications or by email from [email protected].
All documentation related to LivionKey30 and web applications (including General Terms of Sale, General Terms of Use and Privacy Policy) are available on our support pages https://support.livionkey.com. Please study documentation carefully.
Remember:
Refer to our collection of articles for more detailed instructions and troubleshooting tips.
If you encounter any issues or have questions, please don't hesitate to contact our support team.